石膏找平顾名思义就是使用石膏板或是石膏粉与胶调和进行墙面或是天花表面不平整范围的填平工作。这种方法可以进行局部找平且不需要将地面抬高，施工起来比较方便，价格相对来说较为便宜。济南石膏粉找平墙面步骤：

Gypsum leveling, as the name suggests, is the use of gypsum board or gypsum powder mixed with glue to fill in the uneven areas of the wall or ceiling surface. This method can perform local leveling without raising the ground, making construction more convenient and relatively inexpensive. Jinan gypsum powder leveling wall steps:

1

one

先对墙面进行清理。如果墙面有裂缝、孔洞等情况的话，可以先嵌入石膏粉将它们填补平整。

Clean the wall first. If there are cracks, holes, etc. on the wall, you can first embed gypsum powder to fill them flat.

2

two

涂刷界面剂，防止基层开裂。使用滚筒均匀涂刷，阴阳角区域用涂刷满浆，涂刷之后注意保持清洁。

Apply interface agent to prevent cracking of the base layer. Use a roller to evenly brush, and fill the internal and external corners with paint. After brushing, pay attention to maintaining cleanliness.

3

three

防开裂处理。已经开裂的区域先做修补，使用抹刀开八字缝，用石膏刷清扫粉尘，直接铺贴牛皮纸，涂刷石膏，再使用网格布铺满墙面，使两块布之间搭接严密，重新叠加部分不低于50mm。

Anti cracking treatment. The area that has already cracked should be repaired first. Use a trowel to open a zigzag joint, use a gypsum brush to clean the dust, directly apply kraft paper, apply gypsum, and then use a grid cloth to cover the wall surface, so that the overlap between the two pieces of cloth is tight, and the re overlapping part should not be less than 50mm.

4

four

接缝处理。不同材质交接处粘贴接缝时，需要粘贴平整牢固。

Joint treatment. When pasting joints at the junction of different materials, it is necessary to stick them flat and firmly.

5

five

阴阳角弹线。用水平仪在墙面上弹出水平线、垂直线。和顶棚水平线。用石膏粉将边角区域不平整的地方刮平，之后确定墙面大面积平整度的控制线。

Snap the lines at the internal and external corners. Use a spirit level to mark horizontal and vertical lines on the wall. And the horizontal line of the ceiling. Use gypsum powder to scrape off uneven areas at the edges and corners, and then determine the control line for the large area flatness of the wall.

6

six

粉刷基层。根据已经标记好的控制线，批刮石膏。将石膏粉与清水按照比例调兑、搅拌均匀，并在规定的时间内使用完。如果批刮的厚度不超过10mm，则需要铺贴一层网格布，之后再批刮一层石膏。

Painting the base layer. According to the marked control line, apply plaster in batches. Mix gypsum powder and clean water in proportion, stir evenly, and use it within the specified time. If the thickness of the batch scraping does not exceed 10mm, a layer of grid cloth needs to be laid and then a layer of gypsum needs to be scraped.

7

seven

面层施工。基层的石膏层干燥之后，需要在面层涂刷一层石膏，批刮满浆，并找平粗糙的表面，使面层光滑平整。接缝处理。不同材质交接处粘贴接缝时，需要粘贴平整牢固。

Surface layer construction. After the gypsum layer of the base layer is dry, it is necessary to apply a layer of gypsum on the surface layer, scrape the paste thoroughly, and level the rough surface to make the surface layer smooth and flat. Joint treatment. When pasting joints at the junction of different materials, it is necessary to stick them flat and firmly.

此外石膏找平和刮腻子的施工方式是有一些差异，材料也不同。正常情况下石膏适用于内部墙面施工，腻子具有室内外施工的不同点，可以根据自己的需求来施工。石膏更多的是做局部找平处理，腻子更适合做大面积批刮施工。更多相关内容就来我们网站咨询！

In addition, there are some differences in the construction methods and materials of gypsum leveling and putty application. Under normal circumstances, gypsum is suitable for internal wall construction, while putty has different characteristics for indoor and outdoor construction, and can be constructed according to one's own needs. Gypsum is mainly used for local leveling, while putty is more suitable for large-scale batch scraping construction. For more related content, come to our website consulting service