dafa大发手机版_dafa手机版官网

欢迎您浏览济南dafa手机版官网,主营:济南腻子粉,济南石膏粉,济南抹面砂浆等建筑装饰材料,大量批发,欢迎咨询。

专注绿色建筑装饰材料

经营管理理念:让客户用的放心!

24小时服务热线:

13864111871

当前位置: 首页 - 新闻动态 > 公司新闻
公司新闻
联系我们

济南福华建材厂

联系人:吴老师 

电话:13864111871 

手机:13864111871
          0531-81901300
地址:山东省济南市高新开发区巨野河办事处山圈村西


外墙腻子粉掉粉的原因以及解决方法

来源: 日期:2023-02-17 发布人:

墙面装修时刮腻子粉一般需要2遍,刮腻子也容易产生很多问题,其中掉粉是比较严重的问题,腻子掉粉指的是腻子批刮上墙并经过一段时间干固后,用手指压按揉搓墙面,手上沾满白粉末,并且部分粉末掉落墙体。下面济南腻子粉厂家来讲讲外墙腻子粉掉粉的原因以及解决方法。
When decorating the wall, it usually takes two times to apply putty powder, and it is easy to cause many problems when applying putty. Among them, powder falling is a relatively serious problem. The putty powder falling refers to that after the putty is applied to the wall in batches and dried for a period of time, the wall is rubbed with finger pressure, and the hands are covered with white powder, and some powder falls off the wall. Next, Jinan putty powder manufacturer will talk about the causes and solutions of the putty powder falling off the exterior wall.
外墙腻子粉掉粉原因
Reasons for peeling of exterior wall putty powder
1、材料本身及其配比问题;
1. Material itself and its proportion;
2、施工问题:涂抹过薄;加水后搅拌不充分,助剂没有完全发挥作用;
2. Construction problem: too thin coating; The mixing is not sufficient after adding water, and the auxiliary agent does not fully play its role;
3、气候因素:高温干燥、强光照射、强风气候,容易失水过快;
3. Climate factors: high temperature, dry, strong light, strong wind, easy to lose water too fast;
4、基层受潮或不牢固;
4. The base is damp or insecure;
5、基层吸水率太高(墙面太干燥),尤其是翻新墙面,导致腻子干燥速度过快,没有充足的水分进行固化;
5. The water absorption of the base layer is too high (the wall surface is too dry), especially the renovated wall surface, resulting in the drying speed of the putty is too fast, and there is not enough water for curing;
济南腻子粉
6、产品超过保质期,粘结力度大幅度下降;
6. When the product exceeds the shelf life, the bonding strength decreases significantly;
7、产品储存不当,吸潮后粘结力大幅度下降。
7. Due to improper storage of the product, the adhesive force decreases greatly after moisture absorption.
8、腻子粉抛光时间掌握不好,表面已经干燥后再进行抛光处理就答易脱粉。
8. The polishing time of putty powder is not well controlled. If the surface is dry and then polished, it will be easy to remove the powder.
避免腻子掉粉的解决方法
Solution to avoid putty powder falling
1、对材料质量进行严格把关。
1. Strictly control the quality of materials.
2、基层吸水率太高导致腻子干燥太快,没有水分进行固化而起粉,解决办法就是刮腻子之前提前先用清水润湿尤其是翻新墙面。
2. The high water absorption of the base layer causes the putty to dry too quickly, and there is no water to cure and powder. The solution is to wet the putty with water in advance, especially the renovated wall.
3、基层受潮或不牢固:基层进行防水处理,铲除不牢固的基层后用抹灰材料找平后再刮腻子。
3. Damp or insecure base course: the base course shall be subject to waterproof treatment, and the unstable base course shall be removed and leveled with plastering materials before puttying.
4、天或高温强风气候条件下,在施刮腻子前好先用清水润湿墙面,墙面表面无明水后即可施刮腻子。
4. In weather or high temperature and strong wind conditions, wet the wall with clean water before applying putty, and apply putty after there is no open water on the wall surface.
5、产品一定要在保质期内使用,如果超过保质期,必须进行试刮,经检验合格后,再行施工。
5. The product must be used within the shelf life. If it exceeds the shelf life, it must be scraped and tested before construction.
6、产品一定要注意防水处理,应存在阴凉干燥处。
6. The product must be waterproof and stored in a cool and dry place.
此外腻子粉掉粉可能是因为材料本身及其配比,还和施工问题、气候因素都有关系。建议您在使用产品前后多去了解相应的内容问题以及预防措施,更好的进行施工。关注我们了解更多事项!
In addition, the putty powder may fall due to the material itself and its ratio, and also related to construction problems and climate factors. It is recommended that you learn more about the corresponding content problems and preventive measures before and after using the product to better carry out construction. Follow us Learn more!