如果我们根据抹面砂浆的使用部位和功能来进行划分，可以将抹面砂浆分为普通的抹面砂浆、装饰砂浆，以及一些特殊功能的抹面砂浆。下面跟着小编来了解济南抹面砂浆的配合比以及检测项目相关内容吧。

If we divide the plastering mortar according to the use position and function, we can divide the plastering mortar into ordinary plastering mortar, decorative mortar and some special function plastering mortar. Let's follow the Xiaobian to learn about the mix proportion of Jinan plastering mortar and the relevant contents of the test items.

抹面砂浆的配合比

Mix proportion of plastering mortar

一种是用于砖墙表面的一些抹面砂浆。这类抹面砂浆中石灰和沙子的比例是1:2到1:4之间。

One is some plastering mortar used for the surface of brick wall. The ratio of lime to sand in this type of plastering mortar is between 1:2 and 1:4.

二种是适用于一些干燥环境的墙体表面的抹面砂浆。这时它的材料比例是石灰，黏土，沙子的比例是1:1:4到1:1:8之间。

The second is the plastering mortar suitable for the wall surface in some dry environments. At this time, the proportion of lime, clay and sand is between 1:1:4 and 1:1:8.

三种是使用在一些不太潮湿的房间的墙面和天花的砂浆。此时的材料的比例是石灰比上石膏比上沙子的比例是1:0.6:2到1:1:3之间。

The third is the mortar used on the walls and ceilings of some rooms that are not too humid. The ratio of lime to gypsum to sand is 1:0.6:2 to 1:1:3.

四种是使用于一些特别潮湿的，像浴室、厨房等部位的墙面的抹面砂浆的材料比例是1:3到1:2.5。

The fourth is the plastering mortar used for the walls of some particularly humid places, such as bathrooms and kitchens. The material ratio is 1:3 to 1:2.5.

五种是用于普通的地面，顶板或者墙面的面层的抹面砂浆，它的材料比例是1:2到1:1.5。

The fifth type is the plastering mortar used for the surface course of ordinary ground, roof or wall, and its material ratio is 1:2 to 1:1.5.

抹面砂浆需要检测的项目

Items to be tested for plastering mortar

成品的抹面砂浆，在出厂以后都会配有出厂的小票。小票上会写明检查的项目。而且抹面砂浆会有相应的检测报告。通过这些我们都可以发现，抹面砂浆主要检测的项包括：砂浆的稠度，砂浆的保水率，抗压强度，拉伸粘接强度。

The finished plastering mortar will be provided with a factory receipt after delivery. The ticket will indicate the items to be inspected. And the plastering mortar will have corresponding test report. From these, we can find that the main test items of plastering mortar include: consistency of mortar, water retention rate of mortar, compressive strength and tensile bonding strength.

抹面砂浆针对以上的项目都需要进行检测。检测的要求是同一个生产厂家的，同一品种，同一等级，同一批号，且连续进场的砂浆。一般要求砂浆每50立方，做一个检验批，不足50立方时按照一个检验批来算。

Plastering mortar shall be tested for the above items. The testing requirements are the mortar of the same manufacturer, the same type, the same grade, the same batch number, and continuously mobilized. Generally, one inspection lot shall be made for every 50 cubic meters of mortar, and less than 50 cubic meters shall be counted as one inspection lot.

此外它的出厂检验包括初凝时间、抗压强度、密度、稠度和收缩率。

In addition, its delivery inspection includes initial setting time, compressive strength, density, consistency and shrinkage.

要注意，抹面砂浆是为了后期装饰使用的，所以都要求具有很好的和易性，这样便于以后施工。二点就是要求有较高的黏结力，这样砂浆层与基层粘接牢固，能保证长期的不开裂，或者是出现空鼓脱落。更多事项就来我们网站咨询吧。

It should be noted that the plastering mortar is used for later decoration, so it is required to have good workability, which is convenient for later construction. The second point is that it is required to have a high adhesive force, so that the mortar layer and the base layer are firmly bonded, which can ensure long-term non cracking, or hollowing out. For more information, please visit our website Consult.